New England Honda Guys
September 21, 2017, 03:27:18 PM *
Welcome, Guest. Please login or register.

Login with username, password and session length
News:
 
  Home Help Search Calendar Login Register  
  Show Posts
Pages: 1 2 [3] 4 5 ... 8
31  General Category / Events / Re: Fall Beer Night October 2013 on: October 24, 2013, 04:55:05 PM
I wish, I promised the lady I would go to help tonight they are getting like 13 dogs in from Puerto Rico

http://thesatoproject.org/

still on for beer/ Ural fixing tomorrow night though
32  General Category / Events / Re: Fall Beer Night October 2013 on: October 24, 2013, 04:22:29 PM
hey guys, turns out I'm volunteering at a dog shelter tonight , so no beer for me, have fun and drink my share for me
33  Motorcycle Stuff / Honda SOHC4's / Re: 750F Problems (Updated w/ Power Outage) on: October 21, 2013, 03:19:25 PM
a decent amperage switch with some 14 gauge wires ending in uninsulated spade terminals is all your need to create your own switch, or forgetting  the switch, some wire with spade terminals to jump the pins
34  General Category / Events / Re: The Annual New England Guys Fall Ride 2013 on: October 21, 2013, 12:18:54 PM
I think a couple people were interested in the emergency cable kit.  It looks plausible and at $15 its a steal.

http://www.venhillusa.com/Universal-Cable-Kits/Venhill-Emergency-Motorcycle-Cable-Repair-Kit-p701.html

Thanks Treeve!

As an alternative, you can buy it at ebay.

http://www.ebay.com/itm/110969868818


thats the kit  I was talking about

oh, andy, I have your meter, when will you be around? I'll drop it off
35  Motorcycle Stuff / Honda SOHC4's / Re: 750F Problems (Updated w/ Power Outage) on: October 21, 2013, 11:47:41 AM
check to make sure the igniton switch harness on the bottom of the switch didn't get disturbed or broken, its right in the area you were in
36  General Category / Events / Re: The Annual New England Guys Fall Ride 2013 on: October 21, 2013, 11:45:21 AM

I didnt realise you had wind deflectors on your bars as well - where did you get them - probably cheaper than my barkbusters.

my cold fingers would like to know too!

thanks guys I had fun, it was nice to finally ride with you guys

 I was a little confused as to what everyone was doing on south street in needham so I went straight and went home via center street
37  Motorcycle Stuff / Honda SOHC4's / Re: 750F Master Cylinder Rebuild on: October 08, 2013, 09:41:34 AM
good deal, if you need crush washers I have a butt load of them
38  Motorcycle Stuff / Honda SOHC4's / Re: 750F Master Cylinder Rebuild on: October 07, 2013, 11:41:57 AM
on my F the whole assembly was so rusted and horrible that no amount of nails, ring pliers, or modified ring pliers would get it out. Motion pro makes a set for this use, if I had to do it again I'd buy those

my solution was dropping it off at the local motorcycle shop near my work after everyone in work including the machinist tried to get them out and failed

I think I paid like $10 or so and they got it out, not sure what they did or if I want to know what they did, but it worked the innards were one rusty piece surrounded with rusty goo, it was pretty bad
39  Motorcycle Stuff / Other Bikes / Re: R.I.P. Ural on: October 07, 2013, 11:37:50 AM
okay, looks like you got the rear support bearing off, are there more bearing in the back? if you need help I can stop by after work some day
40  General Category / General Discussion / Re: You know its that time of year when..... on: September 24, 2013, 12:52:30 PM
added to my calender, I will try to attend!

41  Motorcycle Stuff / Other Bikes / Re: R.I.P. Ural on: September 23, 2013, 09:42:53 AM
back in town look me up if you need something made
42  General Category / General Discussion / Re: You know its that time of year when..... on: September 23, 2013, 09:41:27 AM
I'm back in town after being away on location for work the past 2 or three weeks, any consensus on the day or location yet?
43  General Category / General Discussion / Re: You know its that time of year when..... on: September 09, 2013, 03:34:14 PM
how about here in CT?

https://plus.google.com/117195862722211202064/about?gl=us&hl=en

bonus is we can go on a ferry ride too
44  Motorcycle Stuff / Other Bikes / Re: R.I.P. Ural on: September 09, 2013, 03:23:29 PM
no prob, thats just simple lathe work, I made a set of seal drivers for a buddies fork seals, I think I have enough scrap material around to make most anything you might need
45  Motorcycle Stuff / Other Bikes / Re: R.I.P. Ural on: September 09, 2013, 03:02:19 PM
I'll help how i can, although most of my September is taken up with work trips.

if needed I know a good machinist who is very motorcycle friendly. or if you need a puller tool, or shaft seal install tool I can make one up on the lather or mill, I'd had very good luck making bearing and seal install drivers
Pages: 1 2 [3] 4 5 ... 8
Powered by MySQL Powered by PHP Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Valid XHTML 1.0! Valid CSS!